SEA 9210 Multifunction I/O Module - Configuration

SEA 9210 Module
Mandatory
Reset choice
€0.00*
SEA 9210 Multifunction I/O Module
Repair & Warranty Program
Reset choice
€0.00*

Product information "SEA 9210 Multifunction I/O Module - Configuration"

  • Multiple channel types in one module
  • 3 Differential analog inputs, 0 to 36 V, 16 bit, 1.1 kS/s
  • 2 Differential analog inputs, ± 80mV, 16 bit, 1.3 kS/s to measure current via shunt
  • 4 Digital inputs, max. 30 V, 5 V-TTL-logic, max. 18 kHz
  • 4 Relay outputs, max. 48 V (1A), max. 50 Hz
  • 6 direct FPGA I/O's, 5 V CMOS-logic (each with 3 inputs and outputs), max. 10 MHz
  • Internal voltage source, switchable (3.3 / 5 VDC)
  • Operating temperature range -40 to +70 °C

Details
The SEA 9210 Multifunction I/O module for NI CompactRIO™ is a universal, compact and cost-effective solution for applications that require only few channels, but different channel types. The combination of analog inputs, binary in- and outputs and direct FPGA lines makes the SEA 9210 suitable for a wide range of applications, for example:
  • Diagnosis and monitoring of autonomous CompactRIO systems (System status, supply status...)
  • Supervision of environment parameter (temperature, pressure, humidity, air quality...)
  • Supervision of mechanical stress (shock, vibration...)
The module offers 3 analog channels for voltage measurements and 2 analog channels for current measurements (over an external shunt resistor). Two voltage channels and two current channels share a common Analog-Digital converter (ADC) respectively, enabling el. power measurements on two independent channels. The basic function of the analog channels is shown in the image SEA 9210 Analog Input above. The 4 digital inputs can be used to monitor binary system states (e.g. 'Door Open!'). The wide input range offers a great tolerance with respect to the system signal levels. The 4 digital outputs can be used to control system components (e.g. switches, lamps, etc.).
The SEA 9210 Multifunction I/O Module offers direct FPGA lines along with an integrated power source to incorporate devices with digital interfaces. Typically, these devices are digital sensors with a digital SPI, I2C or similar communication interface. These sensors often require an external power supply, which can be provided by the integrated power source of the module. All I/O channels are insulated against the backplane. The principle of function is shown in the image SEA 9210 Block Diagram above.

System Requirements
  • See tab Product FAQ

Scope of Delivery
  • 1 * SEA 9210 incl. 1* connector block (60000083)
  • 1 * Printed hardware manual incl. operation instructions, safety guidelines and specifications


CompactRIO Products Home
  • What are the requirements for a development environment?

    PC with the software as follows:

    •   JKI VI Package Manager (VIPM) – latest available version
    •   SEA 9210 driver software
    •   NI LabVIEW™ Development environment 2017 or higher
    •   NI LabVIEW Real-Time 2017 or higher
    •   NI LabVIEW FPGA 2017 or higher + suitable Xilinx tools
    •   NI CompactRIO™ drivers 2017 or higher

    (Limited compatibility with NI cRIO-904x/905x/906x. For further questions please contact techsupport@sea-gmbh.com)
  • What are the requirements for a run-time environment?

    NI CompactRIO™ system with the software as follows:

    •   NI LabVIEW™ Run-Time Engine / LabVIEW Run-Time Engine for Real-Time targets (standard installation)

    (Limited compatibility with NI cRIO-904x/905x/906x. For further questions please contact techsupport@sea-gmbh.com)