cRIO module with 3 digital EnDat 2 interfaces to connect absolute digital position encoders from Heidenhain with the CompactRIO™ system from NI™.DetailsThe position can be readout at high speed and with digital accuracy. The build in FPGA supports EnDat Clock Speeds of up to 8 MHz and allows the synchronous read out of 3 axis in parallel. Besides the digital position data also sensor or calibration information can be readout or written. The software driver access to the position data can be done directly within the LabVIEW FPGA software via IO Nodes and Method Nodes. The digital connection and power supply of the sensors can be done directly via the build in M12 connectors. Look for EnDat encoders at http://www.heidenhain.com/en_US/products-and-applications/angle-measurement/rotary-encoders/.Driver software is available via download link.Scope of delivery1 * SEA 9510 (60000006)1 * Printed hardware manual incl. operation instructions, safety guidelines and specificationsAccessorySensor Cable for BiSS/EnDat Modules (61000607), is mandatory for the operationCompactRIO Products Home
cRIO BiSS-C/SSI interface module to connect up to 3 absolute digital position encoders for use with the NI CompactRIO™ system or R Series Expansion chassis.DetailsSEA 9521 BiSS Interface Module with 3 BiSS-C interfaces to connect absolute digital position encoder from various vendors for use with the CompactRIO system from NI™. The position can be readout at high speed and with digital accuracy. The build in FPGA supports BiSS clock speeds of up to 8 MHz and allows the read out of 3 channels. Besides the digital position data also sensor or calibration information can be readout or written. Module supports optional also the SSI protocol. The software driver access to the position data can be done directly within the LabVIEW FPGA software via IO Nodes and Method Nodes. The digital connection and power supply of the sensors can be done directly via the build in M12 connectors.Approved rotary encoder you can get from various vendors e.g. www.hengstler.com or www.renishaw.com.Scope of delivery1 * SEA 9521 (60000069)1 * Printed hardware manual incl. operation instructions, safety guidelines and specifications Accessory Sensor Cable for BiSS/EnDat Modules (61000607), is mandatory for the operationCompactRIO Products Home
Supported Standards: IEEE 802.11p–2012, (ETSI ES 202 663, IEEE 1609.4–2010) Frequency bands: 5.850–5.925 GHz, channels 172, 174, 176, 180, 182, 184 Channel bandwidth: 10 MHz, OFDM Modulation Modes: 3, 4.5, 6, 9, 12, 18, 24, 27 Mbps for 10 MHz BW signal Maximum output power: 5.9 GHz: –10 to +23 dBm (± 2 dBm), 5.9 GHz: IEEE 1609 Class C Minimum sensitivity: –97 dBm @ 3 Mbps Operating temperature range: –25 to +55 °C DetailsThe SEA 9719 cRIO module enables communication according to the IEEE 802.11p standard on the NI CompactRIO™ platform. This standard provides a basis for the future Vehicle-to-Anything (V2X) or Car-to-Anything (C2X) technologies. By means of this module regular IEEE 802.11p messages (PHY & MAC layer) can be transmitted and received from within LabVIEW™ user applications. For easy integration a LabVIEW driver with a full set of API functions is available to the developer. The module is connected to a computer system (typically a NI CompactRIO) via Ethernet and the user application runs on the Real-Time controller. No LabVIEW FPGA programming is required. Optionally the module can be operated without an NI CompactRIO Controller (stand alone), by connecting it directly to a PC via Ethernet and running the user application on the PC. The required power of 7 to 30 VDC can be supplied through an adequate cable (see accessory below) from the same power source as the NI CompactRIO system.Delivery Scope1 * SEA 9719 802.11p Communication Module1 * Printed Hardware Manual operation instructions, safety instructions and specifications AccessoryGPS option (66000043) is separately available NotesFor programming and operation a LabVIEW Development Environment 2017 or higher is required (see tab Product FAQ).The software is available as a download.CompactRIO Products Home
Not for USA and Japan! Penta-band in 4G networks: 800 / 900 / 1800 / 2100 / 2600 MHz Dual-band in 3G networks: 900 / 2100 MHz Quad-band in 2G networks: 850 / 900 / 1800 / 1900 MHz Gross data rate up to 100 Mbit/s (DL) and 50 Mbit/s (UL) via LTE Remote access via mobile network (VPN) Text messages via SMS GPS for geo-positioning, timing and synchronization Web-based configuration Operating temperature range from -25 to +60 °C DetailsThe SEA 9744 is a high performance cRIO module for communication in mobile networks of the latest generation (4G). The module operates as a data modem, providing access to the internet via mobile networks. For the communication all currently available standards and protocols like GPRS/EDGE (2G), UMTS/HSPA (3G) or LTE (4G) can be used. The maximum gross data transmission rates are up to 50 Mbit/sec for upload and up to 100 Mbit/sec for download in 4G (LTE) networks. The integrated high-sensitive-50-channel GPS receiver provides an accurate geo-position and precise time information with an update rate of up to 4 Hz. For timing, synchronisation or triggering, the module supplies an additional time pulse output signal (TTL) to the backplane. A built-in backup battery enables cold starts within few seconds for a fast GPS position determination (GPS fix). SEA 9744 provides a socket for connecting of external GPS receivers, if special requirements for the GPS functionality exist. The Mini-SIM card reader is located on the backside of the module with mechanical lock mechanism. Micro-SIM cards can be used with a corresponding adapter. The module is directly connected by the Ethernet-bridge cable with the CompactRIO Real-Time Controller. The power supply of 7 to 30 VDC can be done with the enclosed power cable via the CompactRIO DC supply.Scope of Delivery1 * SEA 9744 (60000072)1 * Printed hardware manual incl. operation instructions, safety guidelines and specifications AccessoryEthernet-bridge cable (61000051) NotesThis module is made for worldwide operation except USA and Japan. For USA use SEA 9745.This module can be used in all CompactRIO systems with FPGA backplane. The use in CompactDAQ systems with real-time controller (e.g. NI cDAQ-9132) or stand-alone is also possible if no GPS data is needed directly in the FPGA (see tab Product FAQ).CompactRIO Products Home
Only for USA (AT&T, T-Mobile)! Tri-band in 4G networks: 700 / 1700 (AWS, B4) / 2100 MHz Tri-band in 3G networks: 850 / 1900 / 2100 MHz Quad-band in 2G networks: 850 / 900 / 1800 / 1900 MHz Gross data rate up to 100 Mbit/s (DL) and 50 Mbit/s (UL) via LTE Remote access via mobile network (VPN) Text messages via SMS GPS for geo-positioning, timing and synchronization Web-based configuration Operating temperature range from -25 to +60 °CDetailsThe SEA 9745 is a high performance cRIO module for communication in mobile networks of the latest generation (4G). The module operates as a data modem, providing access to the internet via mobile networks. For the communication all currently available standards and protocols like GPRS/EDGE (2G), UMTS/HSPA (3G) or LTE (4G) can be used. The maximum gross data transmission rates are up to 50 Mbit/sec for upload and up to 100 Mbit/sec for download in 4G (LTE) networks.The integrated high-sensitive-50-channel GPS receiver provides an accurate geo-position and precise time information with an update rate of up to 4 Hz. For timing, synchronisation or triggering, the module supplies an additional time pulse output signal (TTL) to the backplane. A built-in backup battery enables cold starts within few seconds for a fast GPS position determination (GPS fix). SEA 9745 provides a socket for connecting of external GPS receivers, if special requirements for the GPS functionality exist.The Mini-SIM card reader is located on the backside of the module with mechanical lock mechanism. Micro-SIM cards can be used with a corresponding adapter.The module is directly connected by the Ethernet-bridge cable with the CompactRIO Real-Time Controller. The power supply of 7 to 30 VDC can be done with the enclosed power cable via the CompactRIO DC supply.Scope of Delivery1 * SEA 9745 (60000070)1 * Printed hardware manual incl. operation instructions, safety guidelines and specificationsAccessory Ethernet-bridge cable (61000051)Notes This module is made for operation in USA. For other countries use SEA 9744.This module can be used in all CompactRIO systems with FPGA backplane. The use in CompactDAQ systems with real-time controller (eg NI cDAQ-9132) or stand-alone is also possible if no GPS data is needed directly in the FPGA (see tab Product FAQ).CompactRIO Products Home